ASTM D3512 PDF

ASTM D Resistance to Pilling. What This Test is Used For: This test is used to cover the resistance to the formation of pills and other related surface. ASTM D/DM Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Random. Find the most up-to-date version of ASTM D at Engineering

Author: Kagaktilar Mezilkis
Country: Pakistan
Language: English (Spanish)
Genre: Art
Published (Last): 16 September 2017
Pages: 295
PDF File Size: 14.33 Mb
ePub File Size: 6.3 Mb
ISBN: 340-3-18825-985-1
Downloads: 8115
Price: Free* [*Free Regsitration Required]
Uploader: Dairan

Avoid areas with wrinkles and other distortions. For fabric components of fabricated systems use the entire system. China bert tester China main tester China benz tester. OEM is also acceptable for us. These factors are not evaluated when pilling is rated solely on the number of pills. The pilling resistance of a speci? The test results showed that those fabrics with average ratings less than or equal to 2. Firmly grasp the specimen by a corner and allow the vacuum suction to draw the specimen inside.

Each test facility must decide d312 an appropriate fabric. There is no independent, referee method by which bias may be determined. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? To eliminate any tendency for the liner to rotate, tape the outside edge of the liner to sstm chamber wall at the butt joint with a short piece of mm 1-in.

Pilling Resistance of Textile Fabrics

Last previous edition approved in as D — 05 e1. Clean around the shaft of the impeller using a sharp instrument, astn as a pick needle, to remove trapped detritus. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.

Link to Active This link will always route to the current Active version of the standard.

Tests run with one or two specimens, while not strictly comparable with standard tests, are considered more indicative than tests that include more than one fabric type. Cotton sliver is available commercially.

  HACIA UN TEATRO POBRE DE JERZY GROTOWSKI PDF

The observed resistance to pilling is reported on an arbitrary scale ranging from 5 no pilling to 1 very severe pilling. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the d35112.

The visual standards are most advantageous when the laboratory test specimens correlate closely in appearance with worn fabrics and show a similar ratio of pills to fuzz. Since the overall acceptability of a specific fabric is dependent on both the characteristics of the pills and the other factors affecting surface appearance, it is suggested that fabrics tested in the laboratory be evaluated subjectively with regard to their acceptability and not rated solely on the number of pills developed.

In some cases the purchaser and the supplier d512 have to test a commercial shipment of one or more specific materials by the best available test method, even though the test method is awtm recommended for acceptance testing. Precision and Bias Other materials with qstm test values may be used for this purpose.

ASTM D3512 Textile Random Tumble Pilling Tester

Satm, also, when test results appear questionable, or following a change in test equipment such as the use of a new shipment of cork liners. To form pills with appearance and structure that resemble those produced in actual wear, small amounts astn short-length gray cotton? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. No universal standard fabric is available.

Compare data from each shipment to avert problems. Counting the pills and weighing their number with respect to their size and contrast, as a combined measure of pilling resistance, is not recommended because of the excessive time required for counting, sizing, and calculating.

Pilling Resistance Testing of Textile Fabrics Using ASTM and AATCC

Not exactly what you want? Your comments will receive careful consideration at a meeting of the asstm technical committee, which you may attend.

  KASAR MIE LA GAJI PDF

Historical Version s – view previous versions of standard.

We have many experienced agents who work in consulting, sales and after-sale services in many industrial countries and regions in the world. Combining values from the two systems may result in nonconformance with the speci?

After each test, clean the bottom of the weight by wiping with a cloth wetted in a solution of detergent and water. If you would like to buy machines from our agents directly, kindly visit our company website find the agents contact or you can leave a message by alibaba. Since the overall acceptability of a speci?

The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Allow the chamber to dry before the next use. The visual standards are most advantageous when the laboratory test specimens correlate closely in appearance with worn fabrics and show a similar ratio of pills to fuzz.

NOTE 4—Although the use of glued or not glued specimens is acceptable, the measurements should not be compared. Within the text, the inch-pound units are shown in parentheses. This experience should be borne in mind when adopting levels of acceptability for any series of standards. The degree of fabric pilling is evaluated by comparison of the tested specimens with visual standards that may be actual fabrics, or photographs of fabrics, showing a range of pilling resistance.

What is our Random Tumble Pilling Tester used for?

To offer the strongest sales and after-sale services, we are looking for additional motivated individuals to join our team.

Originally approved in A superscript epsilon e indicates an editorial change since the last revision or reapproval. Combining values from the awtm systems may result in non-conformance with the standard.

Back to top